Viewing production machinery during a foreign customer visit can create significant export control exposure, even when no drawings or files change hands. Manufacturers must determine what the visitor can observe, whether that information is controlled under the ITAR or EAR, and whether authorization is required before access occurs.
Equipment Classification and Technology Classification Are Separate
Production machinery does not automatically become ITAR-controlled merely because it manufactured a defense article or first produced an item listed on the U.S. Munitions List. The analysis generally begins with the machine itself, followed by a separate assessment of the technical data, technology, processes, and assistance that a foreign visitor could receive.
Prior ITAR Production Does Not Determine the Result
The order in which products were manufactured is not usually dispositive. A machine that first produced an ITAR-controlled article and later produced an EAR-controlled commercial item does not necessarily inherit the highest classification of everything it has ever made.
Instead, the company should determine whether the equipment is described by a U.S. Munitions List category, is specially designed for a defense article, or is otherwise subject to the EAR. The specially designed analysis can depend on engineering intent, configuration, performance characteristics, development history, and applicable exclusions. Missing design records make the analysis more difficult, but uncertainty is not a reliable basis for treating the machinery as uncontrolled.
Physical changes between production runs may be relevant. Specialized tooling, fixtures, software, tolerances, calibration settings, or modifications required only for defense articles could indicate that controlled information is embodied in the production setup. Conversely, ordinary commercial machinery used without defense-specific adaptation may support a different classification conclusion.
The Visitor May See Controlled Information Even if the Machine Is Uncontrolled
A commercially available machine can still expose ITAR technical data or EAR technology. Visible control settings, process sequencing, tooling geometry, inspection criteria, material treatments, production rates, tolerances, and operator instructions may reveal information required to develop, produce, operate, or maintain a controlled item.
The central question is therefore not simply, “What is the machine?” It is also, “What controlled knowledge can the visitor obtain by observing the machine, process, personnel, displays, and resulting product?” Both classifications should be documented before the visit.
When Observation Becomes a Controlled Release
Export controls are not limited to shipments, emails, drawings, or technical manuals. Disclosure to a foreign person inside the United States can generally be treated as a release to that person’s relevant foreign country or countries, depending on the applicable ITAR or EAR framework.
Passive Viewing Can Release Technical Data or Technology
Under the ITAR release concepts addressed in 22 CFR 120.56, visual inspection can constitute a release when it reveals controlled technical data. A visitor does not necessarily need to touch the equipment, receive a document, or ask a question. If observation communicates controlled manufacturing information, the release may occur through sight alone.
The same practical risk exists under the EAR. A foreign person who observes controlled production technology, source code, operating parameters, or nonpublic process information may receive technology even if the facility describes the tour as passive. Whether authorization is required typically depends on the technology classification, the visitor’s nationality or nationalities, the destination-based controls, and the availability and conditions of any license exception.
A safe analysis focuses on actual access rather than the label assigned to the meeting. Calling an event a customer tour does not prevent an export-controlled release.
A Release Is Not Always the Same as a Defense Service
A defense service under 22 CFR 120.32 generally involves furnishing assistance, including training, to foreign persons in connection with defense articles, or furnishing controlled technical data in specified circumstances. Demonstrating operation, explaining defense-specific production methods, answering technical questions, troubleshooting, or teaching the visitor how to use the machinery may constitute assistance and create defense service concerns.
Mere presence near equipment is not automatically a defense service. Passive viewing, however, can still release ITAR technical data. It may also become part of a defense service when personnel provide explanations or demonstrations that help the visitor manufacture, operate, develop, or maintain a defense article. Companies should analyze the release and defense service issues separately rather than assuming that one determination resolves both.
Building a Controlled Foreign Visitor Process
Foreign national facility visits should be managed as structured export compliance events. A written process allows legal, engineering, security, operations, and commercial teams to identify risks before a visitor reaches the production floor.
Complete Classification and Screening Before Approval
The host should document the visitor’s full legal name, employer, citizenship, additional nationalities, permanent residency, purpose of visit, requested locations, and expected technical discussions. Restricted party screening should cover the individual, employer, affiliates, and other relevant participants. Screening alone does not resolve technology controls, but it can identify separate prohibitions or escalation requirements.
Engineering and trade compliance personnel should then classify the following:
- The production machinery, tooling, software, and related components
- The articles being manufactured during the visit
- Drawings, work instructions, displays, specifications, and process documentation
- Production, development, operation, installation, maintenance, and repair information
- Any technical assistance or demonstrations planned for the customer
If records do not establish whether equipment was specially designed, the company may need a documented jurisdiction and classification review. The October 2026 DDTC proposal concerning specially designed criteria and potential U.S. Munitions List exclusions could eventually affect some mixed-use equipment. It remains a proposal, so current classifications and authorization requirements continue to govern unless and until a final rule takes effect.
Use a Technology Control Plan During the Visit
A technology control plan should define approved routes, accessible rooms, authorized topics, escorts, photography restrictions, device rules, and emergency procedures. Physical barriers, covered displays, locked cabinets, machine shutdowns, temporary signage, and sanitized work areas can prevent inadvertent disclosure.
The host should brief employees not to improvise technical answers. Questions outside the approved scope should be recorded and answered only after compliance review. After the visit, the company should document locations accessed, information discussed, unexpected observations, and any potential deviation. This record supports deemed export compliance and helps determine whether corrective action or voluntary disclosure analysis is appropriate.
- On October 1, 2026, DDTC published a proposed rule (comments due November 30, 2026) revising ITAR definitions, including "specially designed" criteria and new USML exclusions under a proposed Section 120.35. This could affect classification of mixed-use production equipment previously used for ITAR items if it no longer provides a critical military advantage.
- Multiple November 2026 industry analyses reaffirm that visual inspection of production equipment or processes by a foreign national (including a Chinese customer) constitutes a "release" of technical data under 22 CFR 120.56 if it reveals ITAR-controlled information, treating it as a deemed export or potential defense service requiring prior DDTC authorization.
- Recent practitioner guidance (November 2026) emphasizes pre-visit screening, Technology Control Plans, and physical barriers for facility tours involving EAR/ITAR mixed production, as even passive viewing of manufacturing processes can trigger controls without a license or exemption.
- No new BIS or DDTC policy specifically addressing "viewing production machinery" as a standalone defense service was issued in the past 30 days; existing 22 CFR 120.32 and 120.56 definitions continue to apply without amendment.
Frequently Asked Questions
Foreign customer visits often combine commercial objectives with technical access. The following questions address the distinctions most likely to affect authorization and visit planning.
Is Machinery ITAR-Controlled Because It Once Produced an ITAR Article?
Not necessarily. Classification generally depends on whether the machinery itself is covered by the U.S. Munitions List or otherwise meets applicable specially designed criteria. Prior use is relevant evidence, but it is not automatically controlling. Defense-specific modifications, tooling, software, or performance characteristics may materially affect the analysis.
Does Watching a Machine Operate Create a Deemed Export?
It can. If observation reveals controlled ITAR technical data or EAR technology to a foreign person, the viewing may constitute a release. The company should evaluate what the person can actually learn, including information displayed on screens, conveyed through process steps, or inferred from tooling and operating conditions.
Can a Host Demonstrate the Equipment Without Providing a Defense Service?
Possibly, but demonstrations create greater risk than a silent tour. Explaining operation, providing instruction, answering technical questions, or showing defense-specific production methods may amount to furnishing assistance. The scope of the demonstration should be classified and reviewed before the visit, with authorization obtained when required.
Is a License Always Required for a Chinese Visitor?
Not automatically. The answer typically depends on whether controlled information will be released, the applicable ITAR or EAR classification, the visitor’s citizenship and other relevant statuses, and the availability of an exemption or license exception. China-related controls are extensive, so assumptions based on the commercial nature of the visit are inappropriate.
Can Physical Barriers Eliminate the Need for Authorization?
Effective barriers can prevent a controlled release by keeping technical data and technology inaccessible. They do not authorize access that actually occurs. A compliant plan should combine restricted routing, escorts, covered information, employee instructions, access logs, and documented limits on discussions rather than relying on a nondisclosure agreement alone.
How Stable Software Can Help
Supporting Brokers and Their Importer Clients
Foreign visitor controls are only one part of a broader trade compliance environment. Customs brokers also need efficient systems for managing post-entry opportunities while maintaining clear responsibility for filings and client relationships.
Stable Software makes DrawbackAI, flat-license duty drawback software that U.S. customs brokers can white-label for importer clients and use to file under their own filer code. Stable Software charges a flat software license and never takes a percentage of the importer’s refund. This structure allows brokers to retain control of the service, customer relationship, and filing process without sharing refund proceeds with the software provider. Customs brokers evaluating technology for an expanded drawback practice can learn more about Stable Software’s approach for customs brokers.
Resources
| Type | Resource |
|---|---|
| Source | Primary source |


